Zinc gloss renewal
Aluminium gloss appearance
Similar look to new galvanized
For new, bare, rust free metal or galvanised steel
Ideal for touching-
Resists 310 hours of salt spray testing (DIN)
To handle after 1 hour (at 20°C)
Long lasting, rust resilient decorative covering for ferrous and non-
May be employed straight on top of corroded steel.
No requirement for paint primer or undercoat.
Hammerite creates an exceptional layer that not only seals out water but offers resilient cover both interior and exterior.
Abrade smooth materials and get rid of all corrosion and peeling paint using a wire brush.
Eliminate grime, dust particles and oil using watered down cleaning agent. Wash using water that is clean and permit time for it to dry out.
Apply a test area of Hammerite Direct to Rust Metal Paint Hammered onto coated areas and wait for 60 minutes. If you have no reaction implement Hammerite Direct to Rust Metal Paint Hammered straight to work surface.
Should there be a reaction, take off all paint before using Hammerite Direct to Rust Metal Paint Hammered.
On bare zinc, aluminium and galvanised areas use Hammerite Special Metals Primer before you apply Hammerite Direct to Rust Metal Paint Hammered.
Particular measures must be used to prevent breathing in of airborne dirt and dust throughout surface prep work of pre-
Best job application heat range 8-
Gently stir prior to utilization. You should not mix hard.
You should not combine paint from 2 tins or mix colours.
Brush application: Don’t thin. With formerly coated metal in good overall condition, 1 coating ought to be adequate. On bare corroded metal 2 layers are needed. Make certain that all ends and edges are thoroughly coated. Do not over-
Coventional spray application: Thin with Hammerite Brush Cleaner & Thinners at a proportion of 15% Thinners to Paint. Set up spray gun at 25/35psi and apply full fan spray at highest level. Put on 4 thin layers. Allow 1 hour in between coats. See spray apparatus manufacturer’s suggestions for the appropriate and safe use of sprayers.
Touch dry 1-
A Cold Galvanizer 1085 is a fast drying, zinc rich primer based on an epoxy ester resin. Contains pure zinc as pigment and provides cathodic protection to metal.
Contains 86.5% pure zinc
Withstands continuous exposure to temperatures of up to 300 °C
Touch dry after 15 minutes
Ideal for touching-
Single pack rust primer for direct application on slightly moist or dry metal surfaces. Proven formula since 1921!
Minimal surface preparation (manual derusting)
Penetrates the rust to the metal
Expels moisture & air and encapsulates rust
Can be applied on slightly damp surfaces
Durable corrosion protection, both with and without topcoat
In combination with i.a. 7500 Alkythane®, this product can even be used in corrosion class C4 according to ISO 12944.
Metallic sprays combine a bright metallic appearance with the durable protection of a standard topcoat.
Metallic spray: nice finish, good protection
For bare metal and galvanised steel
Usable as topcoat on zinc primers and galvanised
Finish with transparent topcoat for the best result
Ideal for machinery, pumps, toolboxes, etc.
Available in sparkling, gloss and stainless steel
High quality anti-
For on bare or manually derusted metal
To recoat with after 2 hours (at 20°C)
Red for dark topcoats, grey for light topcoats
Lead and chromate free
Coverage: 12 m2 per litre / 2-
Available in brush quality and aerosol
Temporary metal protection
Up to 1 year corrosion protection outside
Ideal for construction, storage and transportation
Masks construction deficiencies
12 m² per litre (at 35 micron)
Ideal for spray application
Recoatable with CombiColor® and other coatings
The No. 1. Zinc Coating (Brush)
Matt grey appearance
90% zinc in the dry film (99% pure zinc)
To protect bare, rust free metal and galvanised
Ideal for touching-
Conforms to DIN 50.976 (1983)
Resists 430 hours of salt spray testing (DIN)